Pacific VP30-S Sliding Fire Door Set -/30/30


The Pacific VP30-S sliding fire door set is used where a large opening in a fire separation (up to 10m2) is required to be closed off in the event of a fire and/or in daily use.

The slider may be concealed behind an appropriate cavity wall. Automatic opening and closing is not currently available for Sliding Fire Doors. 

The VP30-S is a sliding fire door set. The door leaf can be faced in plywood or steel sheet, and is capped with steel channel to 4 edges and hung from a sliding track system.

A counterweight system, released by a fusible link or electromagnetic hold open devices that are linked to a fire detection system, closes the door leaf in the event of a fire.

For higher fire ratings and larger sized doors refer to the VP240-S slider.

The VP30-S is not available as a smoke control door set.

This door type is suitable for interior installation only.

The thickness of the VP30-S door leaf is 65mm with an approximate leaf weight of at least 31kg/m2

 Wall Type Fire Resistance Rating
Door Application Max Leaf
Height (mm)
Max Leaf
Width (mm)
Timber Stud Wall
Masonry Wall
 -/30/30 Single 4000 3000


  1. The VP30-S is not available as a ‘pair’ door set. Refer to the VP240-S.
  2. The maximum area per sliding door leaf is 10.5m2.

Product Options

Leaf Facings

  • Plywood
  • Steel Sheet 0.9mm

Leaf Edges

The leaf edges listed below are available for the VP30-S door set

Hardware/Closing Systems

A Standard Track System is supplied with this door set.

Standard Closer

Weight and pulley system with self-closure activated by fusible link in the event of fire.

Electromagnetic Closing Weight System

A weight and pulley system modified for electromagnetic release is available. Closure is on fire/smoke detection activated by ESL 445CRT sensors, one mounted each side of the door set to the lintel or ceiling.

Frame Types & Profiles

Please refer to the installation instructions for more information on the frame profiles of this door set.

Meeting Stiles

Not applicable for this door set.

Wall Types


The VP Slider may be hung from a concrete or masonry wall either of precast concrete (thickness 100mm minimum) or grouted blockwork (thickness 190mm minimum).


The VP slider may be installed in a Gib® Systems Drywall confirming to specifications as follows:

GBT180 (VP120-S)
GBT120a, GBT120b, GBTL120 (VP90-S & VP60-S)
GBT60a, GBT60b, GBTL60 (VP30-S)
These specifications are derived from “Gib® Fire Rated Systems”.

Product Optional Extras

Vision Panels

Please contact PDS for information on vision panel options.

Sidelights and Overlights

Not applicable for this door set.


Not applicable for this door set.

Additional Door Options

Cavity Wall System

Thermal Insulation

This door leaf has a thermal insulation rating (R-value) of 0.645 Km2/W.

Technical Compliance Statement

The VP30-S fire door complies with the requirements of NZS 4520 Fire-resistant door sets when installed in accordance with Pacific Doors’ Installation Instructions into a complying fire-resistant wall, and when fitted with approved hardware.

NZS 4520 is referenced in the New Zealand Building Code Acceptable Solutions (Appendix C 6.1.1)

Pacific VP30-S fire doors have been successfully fire-tested in accordance with AS1530.4, as referenced in NZS 4520 and in Appendix C 5.1.1.

The fire resistance achieved by the VP30-S was FRR -/30/30

The VP30-S has been tested to and met the physical endurance requirements of NZS 4520 Appendix A.

The VP30-S fire door will satisfy the requirements of NZBC, B2 “Durability” under conditions of use, installation and maintenance specified by Pacific Doors, or specific contractual guarantees, whichever are overriding.